Thermal-hydraulic design calculations for JRR-3 cold neutron source with the new moderator cell

Tokunaga, Sho; Horiguchi, Hironori; Nakamura, Takemi

JAEA-Technology 2023-001, 37 Pages, 2023/05

JAEA-Technology-2023-001.pdf:1.39MB

The cold neutron source (CNS) of the research reactor JRR-3 converts thermal neutrons generated in the reactor into low-energy cold neutrons by moderating them with liquid hydrogen stored in the moderator cell. Cold neutrons generated by the CNS are transported to experimental instruments using neutron conduits, and are used for many studies of physical properties, mainly in life science, polymer science, environmental science, etc. Improvement of cold neutron intensity is essential to maintain competitiveness with the world's research reactors in neutron science, and we are developing a new CNS that incorporates new knowledge. The current moderator cell for the CNS of JRR-3 is a stainless-steel container which is a canteen bottle type, and the cold neutron intensity can be improved by changing the material and shape. Therefore, the basic specifications of the new moderator cell were changed to aluminum alloy which has a smaller neutron absorption cross section, and the shape was optimized using a Monte Carlo code MCNP. Since these changes in specifications will result in changes in heat generation and heat transfer conditions, the CNS of JRR-3 was re-evaluated in terms of self-regulating characteristic, heat transport limits, heat resistance and pressure resistance, etc., to confirm its feasibility in thermal-hydraulic design. This report summarizes the results of the thermal-hydraulic design evaluation of the new moderator cell.

Development of a miniature electromagnet probe for the measurement of local velocity in heavy liquid metals

Ariyoshi, Gen; Obayashi, Hironari; Sasa, Toshinobu

Journal of Nuclear Science and Technology, 59(9), p.1071 - 1088, 2022/09

https://doi.org/10.1080/00223131.2022.2030824

Electromagnetic induction method is one of the effective techniques for local velocity measurement in heavy liquid metals. Ricou and Vives' probe and Von Weissenfluh's probe are famous instrumentations using a permanent magnet. However, sensitivity and measurement volume of the probes show unexpected variation since demagnetization of the magnet is occurred by temperature increase up to the Curie temperature. In this study, electromagnetic probe incorporating a miniature electromagnet was newly developed to overcome such unexpected variation. The diameter and the length of the sensor was 6 mm and 155 mm, respectively. The sensitivity and the measurement volume of the probe were assessed by measurement of local velocity of flowing mercury in a square channel. To clarify the validity for the measured velocity profiles, numerical velocity profiles were calculated and compared with experiment. And the validity for the measured velocity profiles were confirmed by calculated result.

Integral experiment of I(n, ) using fast neutron source in the "YAYOI" reactor

Nakamura, Shoji; Toh, Yosuke; Kimura, Atsushi; Hatsukawa, Yuichi*; Harada, Hideo

Journal of Nuclear Science and Technology, 59(7), p.851 - 865, 2022/07

https://doi.org/10.1080/00223131.2021.2011794

The present study performed integral experiments of I using a fast-neutron source reactor "YAYOI" of the University of Tokyo to validate evaluated nuclear data libraries. The iodine-129 sample and flux monitors were irradiated by fast neutrons in the Glory hole of the YAYOI reactor. Reaction rates of I were obtained by measurement of decay gamma-rays emitted from I. The validity of the fast-neutron flux spectrum in the Glory hole was confirmed by the ratios of the reaction rates of flux monitors. The experimental reaction rate of I was compared with that calculated with both the fast-neutron flux spectrum and evaluated nuclear data libraries. The present study revealed that the evaluated nuclear data of I cited in JENDL-4.0 should be reduced as much as 18% in neutron energies ranging from 10 keV to 3 MeV, and supported the reported data by Noguere below 100 keV.

Current status and upgrading strategies of J-PARC Materials and Life Science Experimental Facility (MLF) and related components

Teshigawara, Makoto; Nakamura, Mitsutaka; Kinsho, Michikazu; Soyama, Kazuhiko

JAEA-Technology 2021-022, 208 Pages, 2022/02

JAEA-Technology-2021-022.pdf:14.28MB

The Materials and Life science experimental Facility (MLF) is an accelerator driven pulsed spallation neutron and muon source with a 1 MW proton beam. The construction began in 2004, and we started beam operation in 2008. Although problems such as exudation of cooling water from the target container have occurred, as of April 2021, the proton beam power has reached up to 700 kW gradually, and stable operation is being performed. In recent years, the operation experience of the rated 1 MW has been steadily accumulated. Several issues such as the durability of the target container have been revealed according to the increase in the operation time. Aiming at making a further improvement of MLF, we summarized the current status of achievements for the design values, such as accelerator technology (LINAC and RCS), neutron and muon source technology, beam transportation of these particles, detection technology, and neutron and muon instruments. Based on the analysis of the current status, we tried to extract improvement points for upgrade of MLF. Through these works, we will raise new proposals that promote the upgrade of MLF, attracting young people. We would like to lead to the further success of researchers and engineers who will lead the next generation.

Optimization of a slab geometry type cold neutron moderator for RIKEN accelerator-driven compact neutron source

Ma, B.*; Teshigawara, Makoto; Wakabayashi, Yasuo*; Yan, M.*; Hashiguchi, Takao*; Yamagata, Yutaka*; Wang, S.*; Ikeda, Yujiro*; Otake, Yoshie*

Nuclear Instruments and Methods in Physics Research A, 995, p.165079_1 - 165079_7, 2021/04

https://doi.org/10.1016/j.nima.2021.165079

We have optimized a cold neutron moderator to be operated at the RIKEN accelerator-driven compact neutron source. We selected a safe and easy to manage material, mesitylene, as the RANS cold moderator. An efficient moderator system was designed by studying and optimizing a coupled cold neutron moderator of mesitylene at 20 K with a polyethylene (PE) pre-moderator at room temperature in the slab geometry with Particle and Heavy Ion Transport code System (PHITS) simulations. The parameters of mesitylene and PE thickness, the reflector, and the shielding configuration were studied to increase cold neutron intensities. Consequently, an integrated cold neutron intensity of 1.1510n/cm/A at 2 m from the neutron-producing target was finally achieved, which was 12 times higher than that of the current PE moderator. The results showed attractive application prospect of mesitylene as cold neutron moderator material.

New design of high power mercury target vessel of J-PARC

Wakui, Takashi; Wakai, Eiichi; Kogawa, Hiroyuki; Naoe, Takashi; Hanano, Kohei*; Haga, Katsuhiro; Shimada, Tsubasa*; Kanomata, Kenichi*

Materials Science Forum, 1024, p.145 - 150, 2021/03

https://doi.org/10.4028/www.scientific.net/MSF.1024.145

To realize a high beam power operation at the J-PARC, a mercury target vessel covered with water shroud was developed. In the first step, to realize an operation at 500 kW, the basic structure of the initial design was followed and the connection method between the mercury vessel and the water shroud was changed. Additionally, the operation at a beam power of 500 kW was realized in approximately eight months. In the second step, to realize the operation at 1 MW, the new structure in which only rear ends of vessels were connected was investigated. Cooling of the mercury vessel is used to reduce thermal stress and thick vessels of the water shroud are used to increase stiffness for the internal pressure; therefore, it was adopted. The stress in each vessel was lower than the allowable stress based on the pressure vessel code criteria prescribed in the Japan Industrial Standard, and confirmation was obtained that the operation with a beam power of 1 MW could be conducted.

Recent status of the pulsed spallation neutron source at J-PARC

Takada, Hiroshi; Haga, Katsuhiro

JPS Conference Proceedings (Internet), 28, p.081003_1 - 081003_7, 2020/02

https://doi.org/10.7566/JPSCP.28.081003

At the Japan Proton Accelerator Research Complex (J-PARC), the pulsed spallation neutron source has been in operation with a redesigned mercury target vessel from October 2017 to July 2018, during which the operational beam power was restored to 500 kW and the operation with a 1-MW equivalent beam was demonstrated for one hour. The target vessel includes a gas-micro-bubbles injector and a 2-mm-wide narrow mercury flow channel at the front end as measures to suppress the cavitation damage. After the operating period, it was observed that the cavitation damage at the 3-mm-thick front end of the target vessel could be suppressed less than 17.5 m.

Conceptual study on a novel method for detecting nuclear material using a neutron source

Komeda, Masao; Toh, Yosuke

Annals of Nuclear Energy, 135, p.106993_1 - 106993_6, 2020/01

https://doi.org/10.1016/j.anucene.2019.106993

This paper presents a conceptual study of a novel active method using a neutron source. The main feature of this new method is the fast rotation of a neutron source in order to derive the fission neutron counts and applying the counts to detect the nuclear material. Irradiating neutrons to a container that involves nuclear material, the measurement data include both neutrons from the neutron source and fission neutrons. However, if the neutron source is rotated quite fast, the components of the irradiation neutrons and fission neutrons are separated. Since this novel method does not require an expensive D-T tube, this new system is expected to be affordable and easy to assemble.

Improvement of accumulator in cryogenic hydrogen system used for 1-MW pulsed spallation neutron source

Aso, Tomokazu; Tatsumoto, Hideki*; Otsu, Kiichi*; Kawakami, Yoshihiko*; Komori, Shinji*; Muto, Hideki*; Takada, Hiroshi

JAEA-Technology 2019-013, 77 Pages, 2019/09

JAEA-Technology-2019-013.pdf:5.59MB

At Materials and Life Science experimental Facility (MLF) of the Japan Proton Accelerator Research Complex (J-PARC), a 1-MW pulsed spallation neutron source is equipped with a cryogenic hydrogen system which circulates liquid hydrogen (20 K and 1.5 MPa) to convert high energy neutrons generated at a mercury target to cold neutrons at three moderators with removing nuclear heat of 3.8 kW deposited there. The cryogenic system includes an accumulator with a bellows structure in order to absorb pressure fluctuations generated by the nuclear heat deposition in the system. Welded inner bellows of the first accumulator was failured during operation, forcing us to improve the accumulator to have sufficient pressure resistance and longer life-time. We have developed elemental technologies for manufacturing welded bellows of the accumulator by a thick plate with high pressure resistance, succeeding to find optimum welding conditions. We fabricated a prototype bellows block and carried out an endurance test by adding a pressure change of 2 MPa repeatedly. As a result, the prototype bellows was successfully in use exceeding the design life of 10,000 times. Since distortions given during welding and assembling affect functionality and lifetime of the bellows, we set the levelness of each element of the bellows as within 0.1. The improved accumulator has already been in operation for about 25,000 hours as of January 2019, resulting that the number of strokes reached to 16,000. In July 2018, we demonstrated that the accumulator could suppress the pressure fluctuation generated by the 932 kW beam injection as designed. As current operational beam power is 500 kW, the current cryogenic hydrogen system could be applicable for stable operation at higher power in the future.

Experimental evaluation of wall shear stress in a double contraction nozzle using a water mock-up of a liquid Li target for an intense fusion neutron source

Kondo, Hiroo*; Kanemura, Takuji*; Park, C. H.*; Oyaizu, Makoto*; Hirakawa, Yasushi; Furukawa, Tomohiro

Fusion Engineering and Design, 146(Part A), p.285 - 288, 2019/09

https://doi.org/10.1016/j.fusengdes.2018.12.047

Herein, the wall shear stress in a double contraction nozzle has been evaluated experimentally to produce a liquid lithium (Li) target as a beam target for intense fusion neutron sources such as the International Fusion Materials Irradiation Facility (IFMIF), the Advanced Fusion Neutron Source (A-FNS), and the DEMO Oriented Neutron Source (DONES). The boundary layer thickness and wall shear stress are essential physical parameters to understand erosion-corrosion by the high-speed liquid Li flow in the nozzle, which is the key component in producing a stable Li target. Therefore, these parameters were experimentally evaluated using an acrylic mock-up of the target assembly. The velocity distribution in the nozzle was measured by a laser-doppler velocimeter and the momentum thickness along the nozzle wall was calculated using an empirical prediction method. The resulting momentum thickness was used to estimate the variation of the wall shear stress along the nozzle wall. Consequently, the wall shear stress was at the maximum in the second convergent section in front of the nozzle exit.